2016年思科認證CCIE認證考試模擬試題及答案
思科認證主要考試內容是什么?今天yjbys小編為大家分享的是思科認證考試模擬試題及答案，僅供同學們復習參考!
1. Before inserting a new switch in the network, the network administrator checks that the VTP domain name is correct, the VTP mode is set to server, and revision is lower than the switches in the network. The administrator then configures interfaces and trunks, erases existing VLANs, and connects the switch to the network. Following that procedure, there is no connectivity in the network. What is a possible cause of this problem?
之前在網絡中加入了一個新的交換機，網絡管理員檢查VTP域名是正確的。VTP模式設置為 服務器，修訂號也比其他的交換機低。管理員配置接口和Trunk。清空了所有的VLAN后吧 交換機連接入網絡。經過這些操作，交換機沒有任何的網絡連接。這是什么問題?
A. Because the configuration revision of the new switches is lower than the rest of the network, it can change the VLAN database of the other switches. B. As a VTP server, the new switch deleted all VLANs of the network. C. Erasing VLANs increases the VTP configuration revision.
清空VLAN 會影響到VTP的修訂號
D. Since the configuration revision of the network is higher than the new switch, the VLAN database was automatically synchronized.
Answer: C www.Examw.com
2. While deploying a new switch, you accidently connect ports 3/12 and 3/18 together, creating a loop. STP detected it and placed port 3/18 in blocking mode. Why did STP not place port 3/12 in blocking mode instead?
當部署一個新的交換機，你無意的鏈接了3/12/和3/18，形成了一個環路，STP把3/18端口 設置為阻斷端口，為什么沒有把3/12設置為阻斷端口呢?
A. Port 3/12 was already up and forwarding before the loop was created. B. Port priority is based on lowest priority and lowest port number. 因?yàn)槎丝贗D 3/12比較低 C. You connected the wire on port 3/18 last. D. None of the above, it is purely random. Answer: B
3. Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correct BGP session endpoint addresses and the correct BGP session hop-count limit (EBGP multihop). What is a good first test to see if BGP will work across the firewall?
有兩個運行BGP的`路由器連接到防火墻， 一個在inside接口， 一個在outside 接口。 BGP 已經配置并且已經成為了鄰居，包含正確的配置了BGP網絡地址和正確的BGP跳數的限制 (EBGP的多跳設置)，怎么能夠最好的測試BGP工作在防火墻上。
A. Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works, BGP will work, since telnet and BGP
both use TCP to transport data.
用在inside接口上的路由器telnet 到在outside 接口上的路由器。如果telnet 正常工作側說明 BGP能正常工作，因?yàn)閠elnet 和BGP 都是使用TCP 來傳輸數據的
B. Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them, BGP should work, since BGP uses IP to transport packets. C. There is no way to make BGP work across a firewall without special configuration, so there is no simple test that will show you if BGP will work or not, other than trying to start the peering session. D. There is no way to make BGP work across a firewall.
Answer: A
4. Refer to the exhibit. In this network, R1 has been configured to advertise a summary route, 192.168.0.0/22, to R2. R2 has been configured to advertise a summary route, 192.168.0.0/21, to R1. Both routers have been configured to remove the discard route (the route to null created when a summary route is configured) by setting the administrative distance of the discard route to 255.
如圖所示，在這個網絡中，R1通告了192.168.0.0/22的匯總路由給R2， R2通告了192.168.0.0/21的匯總路由給R1。兩臺路由器都配置了匯總路 由的null0 接口來防止路由的環路。發生什么情況，R1能收到一個去192.16 8.3.1的數據包?
What will happen if R1 receives a packet destined to 192.168.3.1? A. The packet will loop between R1 and R2. 這個包在R1和R2之間形成了環路 B. It is not possible to set the administrative distance on a summary to 255. C. The packet will be forwarded to R2, where it will be routed to null0. D. The packet will be dropped by R1, since there is no route to 192.168.3.1.
Answer: A
5. Refer to the exhibit. In this network, R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP?
如圖所示，在這個網絡中 R1配置為在EIGRP中不做自動匯總，那么R3能從R2學到什么 EIGRP的路由信息。
A. 172.30.1.0/24 and 10.1.2.0/24; EIGRP only performs autosummarization at the edge
between two major networks.www.Examw.com
172.30.1.0/24 和 10.1.2.0/24 EIGRP在兩個較大的網絡邊緣只能執行自動匯總。
B. 172.30.0.0/16 and 10.1.2.0/24; R2 will perform autosummarization, although R1 will not. C. Since R2 is configured without autosummarization, it will not propagate the 172.30.1.0/24 route. D. 172.30.0.0/8 and 10.0.0.0/8. Answer: A
【2016年思科認證CCIE認證考試模擬試題及答案】相關文章：
思科CCIE認證考試模擬試題及答案「最新」08-29
思科認證CCIE認證考試簡介09-20
2016年思科認證CNAA考試模擬試題及答案08-29
思科認證CCIE協作實驗考試要點09-29
思科認證CCIE安全考試大綱09-29
思科認證CCNA認證試題及答案中文版10-27